Similar Topics: Cable Assembly
Cable Assemblies
enable IO signal paths.
See Also: Cables, Interconnects, Flying Leads, Instrument Cables, Patchcords
-
product
Cable Assy 78-Pin D-Type F/F 0.5m
40-970-078-0.5m-FF
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Length Network Cable Tester
SC-8108
1. Measure network cable length and determine the distance of breakage point.2. Check wiring error in 5E, 6E, coaxial cable, such as open circuit,short circuit, jumper wire, reverse connection .3. Portable unit with long battery life (wait-case 50 hours).4. Automatically time-delay shut off.5. Self-checking and automatically compensate any change in battery capacity or ambient temperature.
-
product
xDSL Cable Qualifier
ELQ 2+
*Physical parameter measurements on balanced access lines like:ADSL2, ADSL2+, READSL, ADSL, HDSL, SHDSL, ISDN, etc.*Memory for test results*PC software for test result transfer*Demo program for training*320 x 240 dot LCD display with backlight*Selectable English, German or Russian languages
-
product
Cable Assy 37-Pin D-Type M/M 0.5m
40-970-037-0.5m-MM
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 37-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
3-meter Laser Head Cable
10882A
The 10882A 3-meter Laser Head Cable is used to connect the 5519A/B Laser Head to the E1735A USB Axis Module for the 5530Laser CalibrationSystem.
-
product
High Quality Cable Tracker LAN Finder
specification:*Working current:Tester:10mA Receiver:30mA*Signal transfe mode: Digital signal*Signal output level:8Vp-p*Signal transfer distance:3Km*Power:by 2 × DC 9V Battery(not included)
-
product
Multi-purpose Cable Tracer and Non-contact Voltage Detector
168 CB
Standard Electric Works Co., Ltd
● Four transmitter plug types - RJ-11 - RJ-45 - COAX - Alligator clips ● Two unique audible tones: - Fast alternating tone - Slow alternating tone ● Telephone line polarity check - Tip side - Ring side● Cable tracing ● Telephone line status check - Clear line - Busy line - Ringing line ● Continuity check.● Transmitter plug storage.● Easy to store different kinds of transmitter plugs (RJ-11, RJ-45, COAX, and alligator clips).● Easy to carry.● Flashlight function.
-
product
Recloser and Sectionalizer Test Cables
OMICRON offers a comprehensive range of cable packages as an accessory to CMC test sets for testing various recloser and sectionalizer controls.
-
product
Integrated Turbine Rotor Measurement and Assembly Platforms
GeoSpin
Rotary Precision Instruments UK Ltd
Improve productivity and achieve higher levels of quality by reducing inspection times and the need for costly teardowns due to inefficient rotor assembly.GeoSpin has been specifically developed for the measurement and assembly of smaller gas turbine rotors for the aerospace and power generation industries reducing the rate of teardowns by 95%.
-
product
InfiniBand to BNC Cable, AI0-7 for PXIe-4492
787916-01
16-Pin K-Type Male InfiniBand to 8 1-Pin BNC Male, 50 Ohm Coaxial Cable - The SHB4X-8BNC is a coaxial cable that connects data acquisition and control devices.
-
product
Cable Modem Test Platform
Promptlink Communications, Inc.
CMTP has broad support for the mixed environment of DOCSIS 3.0, and earlier devices. Similarly, it supports all DOCSIS/Euro DOCSIS equipment vendors, impartially treating each vendor's devices with maximum performance and minimum hassle.CMTP is fully automated, requiring no user input for testing.CMTP tests the basic Cable Modem, Wi-Fi and EMTA parameters such as signal levels, signal to noise ratio, etc. as well as device throughput and packet loss. For PacketCable devices, CMTP tests each phone port individually, with maximum functionality being tested.CMTP can also be configured to upgrade the firmware of the devices in a multi-step and conditional process.
-
product
GPIB Cable, 2 Meter
10833B
The Keysight 10833B (2 meter) GPIB cable is engineered for exceptional reliability and durability even under the harshest conditions. When you buy Keysight GPIB cables, you can be sure of automatic, seamless compatibility between computers and instruments throughout your system. GPIB interface cables, cards, and software for your computers make it easy for you to access and control instruments and exchange data - and it all starts with the cables to connect your computer and instrument. Keysight GPIB cables are fully compatible with the IEEE 488.1 mechanical specification.
-
product
160 Pin Female LFH to QuadraPaddle Flying Lead Cable, 36", 780009-02
VFL159124-036
Vendor Flying Lead (VFL) Cable, 160 Pin Female LFH to QuadraPaddle Leads, 28AWG Twisted Pair, 160 T/P's, SHARED GROUNDS 80 T/Ps, 168 connection points, CONN: 780009-02, VPC Contact 610138216 - QP RCV (22AWG-28AWG) (5 AMP/25 mΩ MAX), 36" length.
-
product
6”Cable
RCONAF-EC
A 6â€cable transitions from the card edge connector on the RAF-EC-2P (champ 36) to one male HD-15 connector and two shielded RJ-45 connectors.
-
product
Cable Assy 37-Pin D-Type F/F 1m
40-970-037-1m-FF
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21 AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
-
product
Compact Cable Test Van
ETL-15
ETL-15 is compact enough to be mounted even in a minivan, yet contains all the equipment typically found in a fully-featured cable test and fault location system, including burn module, surge wave generator, time-domain reflectometer and high-voltage DC test module.
-
product
Handheld TDR / Cable Fault Locator
RapidTrace 1100
*This TDR / Cable Fault Locator is suitable for testing all Communication CAT (3-6) , Power Cabling , coaxial and mains power cabling*The RapidTrace 1100 TDR / Cable Fault Locator has a 11 measurement ranges from 0.5m to 3500m (3.5km) and is accurate to 1%*The TDR / Cable Fault Locator has 25, 50, 75 & 100ohm Selectable Cable Impedances*Using pre determined gain and pulse width on the TDR / Cable Fault Locator, all major operating and setting parameters can be easily accessed
-
product
WaveLink Temperature Extension cables for Dx10
Dx10-HiTemp
- Choice of 4 GHz or 6 GHz bandwidth models- Up to 5 Vpk-pk dynamic range with low noise- ±3 V offset range- Low loading and high impedance for minimal signal disturbance- Ideal for DDR2, DDR3, LPDDR2- Deluxe soft carrying case- Innovative QuickLink architecture- Wide variety of tips and leads-- Solder-In Lead-- Optional Positioner (Browser) Tip-- Quick Connect Lead-- Square Pin Lead-- HiTemp Solder-In Lead
-
product
50-Pin IDC Connector for Ribbon Cable - Female
40-961-550-F
Ideal for user created termination schemes where the termination is to be remotely connected by a ribbon cable. A mating 50-Pin PCB connector 40-963-550-SM and IDC Breakout with DIN Rail mount 40-967-550-M are also available.
-
product
Low Inductance BNC Cable, VOLT:DC 60V
PX0105A
The Keysight PX0105A is suitable for narrow current pulse measurement down to 10 μs pulse width. It supports the Keysight M9602/03A.
-
product
Cable Length Meter
CLM100
UEi Test & Measurement Instruments
The CLM100 Digital Cable Length Meter is an excellent tool to measure spooled cable/ wire. This best seller is built solid and supplied with a ruggedized boot for reliable field performance. Currently being utilized by major utility companies, electrical contractors, wholesalers, and installers where quick and accurate inventory management or measurements are needed for job accountability. Simply attach the Kelvin Clips to both ends of the cable and adjust the indicator to the size wire being measured. A temperature compensation circuit ensures accuracy by compensating for the temperature of the wire.
-
product
Cable and Antenna Analyzer
iVA-0627A-NC
iVA Cable & Antenna Analyzer System, Type N male connector with Neoprene Soft Case
-
product
Cable & Antenna Analyzer and Vector Network Analyzer
SiteOne 3028
The SiteOne 3028 is a Cable, Antenna Analyzer and a Vector Network Analyzer for cables, antennas and more, a truly handheld instrument. It covers all major communication bands from 50 kHz to 4400 MHz. It has a variety of measurement screens available, in order to accommodate all the different parameters in an antenna installation. These measurement screens can show two simultaneous graphs, from two different parameters in order to bring further clarity to your measurements.
-
product
Cable Assembly, Type-N (m) to Type-N (m), DC to 6.0 GHz
11500B
The Keysight 11500B is a 58 cm (23 in) type-N male to type-N male cable assembly with a frequency range of DC to 6.0 GHz.
-
product
CableEye Cable Testing
A industry-grade, Windows PC driven cable tester with incredible performance yet amazingly simple to operate. CableEye cable testing has found itself in areas as diverse as working in oil/gas mining through avionics and F1 car testing to audio cables at concerts.
-
product
Audio Cable Testers
AudioJog Pro 3
Audio cable tester with SINGLE & DOUBLE ended testing, memory and intermittent fault detection .
-
product
Split-type Cable Fault Location System
Weshine Electric Manufacturing Co., Ltd
Electricity networks have had to become more flexible, reacting more quickly to the changes and needs of higher performance. This demand for flexibility is especially true where multiple generation sources occur, such as the intermittent power from renewables like solar and wind energy. While modern SMART grid technology can quickly identify faults in sub-station and generating units, cable faults can still occur anywhere on the network.
-
product
Cable Assembly, Receiver, QuadraPaddle, 20"
540219010134
Cable Assembly, Receiver, QuadraPaddle, 20"